Western Digital Error 0007 Read Element Failure
Re-test Drive 148 Not Selected Drive not selected. It may also be due to a defective connection. An onboard defect counter has determined the drive has too many errors and should be replaced. Re-Test Drive 586 DRQ Timeout Data ReQuest Timeout. Check This Out
Create and use a new DLG Tools diskette. ECC is a hardware correction technique that corrects errors. The drive has failed and must be replaced. Replace Drive 211 2-9 Uncorr ECC Errors Error Correction Code (ECC) 2 through 9. check my site
Western Digital Error Code 0007
Posts 13,478 how can software fix a bad head? Retest. Quick response time.
This condition occurs when the device's SMART reliability status indicates an impending degrading or default condition. If I disconnected the WD drive the other drive would boot fine. Questions: 1. Western Digital Error Codes There were too many errors found on this drive to be repaired.
Replace Drive 357 DAM 2-9 Data Address Mark. Status Code = 07 (failed Read Test Element), Failure Checkpoint = 97 Please ensure that you are using the proper version of diagnostic utility. If ECC occurs, use Data Lifeguard repair option for additional error correction. http://www.pcguide.com/vb/showthread.php?65809-WD-HDD-quot-Read-Element-Failure-quot-causes-other-drive-not-to-boot Feedback Doctor's Lounge « Previous Thread | Next Thread » Thread Information Users Browsing this Thread There are currently 7 users browsing this thread. (0 members and 7 guests) Posting Permissions
Replace the drive if the error repeats. Read Element Failure Fix Copyright protection & Intellectual property my ass. Results 1 to 9 of 9 Thread: WD HDD: "Read Element Failure" causes other drive not to boot Thread Tools Show Printable Version Email this Page… Subscribe to this Thread… 09-08-2008,01:05 Reply With Quote Quick Navigation Storage Top Site Areas Settings Private Messages Subscriptions Who's Online Search Forums Forums Home Forums Forum Information and General Discussion Forum Announcements and Feedback The PC
Status Code = 07 (failed Read Test Element), Failure Checkpoint = 97
If the errors continue, replace the drive. http://arstechnica.com/civis/viewtopic.php?t=109716 There could be media errors present on this drive. Western Digital Error Code 0007 Re-Test Drive 258 ECC 10+ Error Correction Code. Delete Partitions Error Wd This is the pretest initialization code which indicates a drive is ready to be tested, but has not yet been tested.
If the automatic repair feature is unable to repair these errors, replace the drive. his comment is here Replace the drive if the error repeats. All rights reserved. Using WD Data Lifeguard diagnostic tool give me Error Code 0007 Read Element Failure on quick test and Error Code 225 Too Many Errors on Extended Test. 20 Delete Partitions Error
I did a 'Full Media Scan' and it supposely fixed the problem. What puzzled me was when testing using the windows version of the WD Data Lifeguard diagnostic tool and HDD Health freeware, both sets of S.M.A.R.T. In order for S.M.A.R.T. this contact form Retest.
The WD wouldn't boot either way, which I would understand. Read Element Failure Hitachi This error may also be related to memory issues. Replace Drive 217 2-9 SERVO Errors SERVO 2-9.
Re-test Drive 145 FULL STROKE ERROR Error encountered during full stroke seek.
Replace the drive if the error repeats. Re-test 132 Command Error Command Aborted. Without knowing more about the actual partitioning and the content of the boot.ini file or files it is difficult to be more specific. Wd Bad Sector Repair Tool The errors could be caused by other issues, power supply problems are a real common cause. 10-31-2009, 10:39 PM #7 robertin75 Registered Member Join Date: May 2009 Posts:
Re-test Drive 206 Memory Allocation Error Unable to allocate memory for program structures. This may be due to a media or read/write error. Replace the drive if the error repeats. http://permanentfatalerror.com/western-digital/western-digital-hdd-error-0007.php Local time:05:31 AM Posted 14 April 2013 - 08:37 AM According to Western Digital, the error/status 007 code means the "Self Monitoring, Analysis, and Reporting Technology (SMART) Error returned during SMART
Re-Test Drive 108 Seek Not Complete A Seek command did not complete in the time allotted. It may also happen when the wrong version of diagnostic utility is used. The cable is loose, broken, or not plugged in. http://www.newegg.com/Store/SubCateg...al-Hard-Drives SMILE and post back.
© Copyright 2017 permanentfatalerror.com. All rights reserved.