Welch Allyn 300 Series Error Codes
Are you sure you want to continue?CANCELOKGet the full title to continueGet the full title to continue reading from where you left off, or restart the preview.Restart previewscribd Open/Close Menu Generated Thu, 08 Dec 2016 13:24:58 GMT by s_hp84 (squid/3.5.20) Connector Types The procedures described below require you to disconnect and reconnect ZIF (zero-insertion force) connectors, squeeze-release connectors, and pressure connectors. C13 Battery problem Plug in the wall transformer and charge the battery. Check This Out
Your cache administrator is webmaster. Page 47: Separate The Front And Rear Chassis Disassembly Procedure Separate the Front and Rear Chassis 3. b. Open the printer door and remove the roll of printer paper.
Welch Allyn 300 Series Service Manual
Remove the printer door. Remove the two screws (located on the left side, inside the rear chassis) securing the module to the slots on the left side of the rear chassis. Verify patient type setting.
If the error persists, replace thetemperature board, Use the service utility to verifycompatibility.Error code E37 Printer failure. Disconnect the NIBP hose from the front chassis 5. Remove the side panel and board assembly form the rear chassis. 2. Welch Allyn 53ntp Check patient condition, cuff placement and connection.
December 5, 2014 As economies change, budgets also do accordingly. Welch Allyn 300 Series Vital Signs Monitor Page 67 Disassembly Procedure Remove and Disassemble the Printer Assembly printer-frame “piano” legs are toward the front, extending downward from the assembly. Remove the screw securing the printer board to the printer assembly. http://www.medwrench.com/?community.threads/manufacturerNo/670/forumType/QA/forum/Welch-Allyn-Questions-and-Answers/ Symptom...
Page 78 Replacement Parts Option 010-0232-XX Side-panel Assembly, SpO , MP-506 031-0139-XX Board, SpO , Nellcor MP-506 660-0233-XX Cable Assembly, SpO Main Interface Temperature Option 21327-000 PCB, Temperature Module 630-0211-XX Outside Welch Allyn Error Codes Testing the Monitor Only Use this procedure to test only the monitor SpO function. 1. Remove the two screws securing the board to the side panel. Press .
Welch Allyn 300 Series Vital Signs Monitor
No one is permitted to reproduce or duplicate, in any form, the whole or part of this manual without permission from Welch Allyn. • Welch Allyn will not be responsible for https://www.scribd.com/document/127445843/Servicemanual-Welch-Allyn300 Remove the NIBP board. Welch Allyn 300 Series Service Manual Retake reading. Welch Allyn 420 Service Manual Page 70 Disassemble the Temperature Module Disassembly Procedure 4 screws securing the temperature board to the module housing c.
Error code E32 Factory data failure. his comment is here Wait another 10 seconds, note the current pressure, and verify that it has not dropped more than 8 mmHg (1.1 kPa) below the pressure noted in step 6. The monitor displays the message Service Mode, runs a self-test, and then displays the main software version number (M: 1.00.00). If the error persists, replace the SpO2board.Use theservice utilityto verifycompatibility.Error code E36 Faulty probe. Welch Allyn 52000 Service Manual
P The temperature probe has poor tissue contact. Sign In Upload Page of 78 Go Download Table of ContentsContents TroubleshootingTroublesh.. Page 52 Disassemble the Front Chassis Assembly Disassembly Procedure Printer button Reassembly Notes If you are replacing the keypad and your monitor does not include the thermal printer option, the Printer this contact form Page 42 Welch Allyn Monitor Service Utility Troubleshooting and Repair Service Manual Vital Signs Monitor Series 300...
Push the plastic legs of the printer assembly outward and pull the printer assembly forward to free it from the snap-in seating of the rear chassis bulkhead. Welch Allyn Vital Signs Monitor 6000 Contact customer service. NIBP Reassembly Notes Warning You must characterize the NIPB module whenever you replace any NIBP component (pump, tubing, air filter, check valve, or NIBP module).
All NIBP service must be performed at an authorized Welch Allyn service center. 1.
Page 18: Equipment Required (Use the female end from the cable set) Welch Allyn Monitor Service Utility 840-0676-XX (required for NIBP repair or replacement; not required for functional testing) Service Serial Refer all warranty service to Welch Allyn Factory Service or another authorized Welch Allyn Service Center. Buy the Full Version You're Reading a Free Preview Pages 46 to 93 are not shown in this preview. Welch Allyn 53n00 Page 29 Functional Veriﬁcation Functional Veriﬁcation Procedure % SpO Rate 60 (Motion Artifact not selected) 2.
If the error persists, return the monitor to an authorized service center for replacement of the main board. Remove the keypad. Power the monitor off. 2. navigate here Separate the Front and Rear Chassis 1.
Page 44: Connectors Procedures Overview Disassembly Procedure Connectors Caution All connectors are keyed or coded to facilitate proper connection. Never pull directly on the cable itself. Limitpatient motion. If the Welch Allyn 9600 Calibration Tester (01800-200) is not already warmed up, warm it up as follows: a.
Page 41: Characterizing Nibp Troubleshooting and Repair Welch Allyn Monitor Service Utility Characterizing NIBP To characterize the NIBP module, start the Welch Allyn Monitor Service Utility and click on Characterize NIBP. Both you and our service techs might find this following chart below as good quick reference to the possible causes of these error codes. Carefully tip the upper edge of the main board away from the rear chassis, far enough to access the uppermost connectors on the component side of the board. 5. If the error persists, return themonitor to an authorized service center forreplacement of the main board.Error code E32 Factory data failure.
Verify all cable connections, and then cycle thepower. Page 46: Remove And Disconnect The Battery Remove and Disconnect the Battery Disassembly Procedure Board Connectors Connector Connects With Connector Connects With side panel Main board – J7 NIBP Board Connectors Remove the tubing and the pump. Press to select 0 mmHg (0 kPa) target pressure. 2.
If no leaks are found it is possible there may be an internal leak call tech service. Page 68: Disassemble The Temperature Module Disassemble the Temperature Module Disassembly Procedure Disassemble the Temperature Module Disassembly of the temperature module does NOT require removal of the main board. 1. Page 28 Functional Veriﬁcation Procedure Functional Veriﬁcation Perform one of the following two SpO tests. If the error persists, return themonitor to an authorized service center forreplacement of the main board.Symptom Possible cause Suggested action previous next Problems & Solutions Sponsored Listings Loading Products...
Verify an SpO saturation level of 94 ± 4. 5. Verifythat the paper guideand sensor areproperly attached to the printer chassis.Error code E38 Error E38 always occurs when themonitor is first powered after abattery has been connected.Real-time clock failure.Cycle the power, Check the patient’s condition. SpO2 Error Codes E7 Internal error.
Page 7: Symbols Safety Summary Symbols • Use only grounded tools when inserting, adjusting, or removing static-sensitive components and assemblies. • Remove or insert static-sensitive components and assemblies only with monitor Press several times to select 0 mmHg (0 kPa). b.
© Copyright 2017 permanentfatalerror.com. All rights reserved.